®TMTaylorcraft 26cc BNFAssembly Manual
10 Hangar 9 Taylorcraft 26cc BNF 2. Position the tiller arm on the bottom of the rudder so the front edge is aligned as close to the hinge line as po
11Hangar 9 Taylorcraft 26cc BNF 8. Attach the tail wheel assembly and the aluminum spreader tab on the fuselage using two 3mm x 15mm socket head wood
12 Hangar 9 Taylorcraft 26cc BNF 2. Measure and mark the front lower wood strut 103/4-inch (273mm) and rear lower wood strut 101/2-inch (267mm). The
13Hangar 9 Taylorcraft 26cc BNF 8. The shorter strut can now be attached to the stabilizer using a 4-40 x 5/8-inch button head cap screw, #4 washer,
14 Hangar 9 Taylorcraft 26cc BNF 15. Check the alignment of the fin to the stabilizer to make sure they are perpendicular to each other. Also check t
15Hangar 9 Taylorcraft 26cc BNF 4. Check that the ignition switch is in the off position before connecting the leads to the engine in the following s
16 Hangar 9 Taylorcraft 26cc BNF 9. Thread the screw into the nylon arm included with the engine. 10. Install the included nylon choke arm on the br
17Hangar 9 Taylorcraft 26cc BNF 3. Remove the plug for the fill line from the cowl. While guiding the cowl on the fuselage, guide the line from the T
18 Hangar 9 Taylorcraft 26cc BNF 9. The spinner can now be attached using the screw provided and a 4mm hex wrench. Make sure the spinner does not con
19Hangar 9 Taylorcraft 26cc BNFDrawing not to scaleRudder and elevatorattach clevisto this hole 4. When connecting the clevises to the rudder, make s
2 Hangar 9 Taylorcraft 26cc BNF WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Fail
20 Hangar 9 Taylorcraft 26cc BNF 3. Apply 2–3 drops of thin CA in each of the holes to harden the threads in the surrounding wood. This will make the
21Hangar 9 Taylorcraft 26cc BNFNote: Do not over-tighten the hardware that secures the wing struts to the fittings so the struts can be folded in for
22 Hangar 9 Taylorcraft 26cc BNF 5. Secure the wing to the fuselage using the nylon wing bolt removed in step 1. Attach the struts to the fitting on
23Hangar 9 Taylorcraft 26cc BNF 2. When balancing your model, make sure it is assembled and ready for flight with the fuel tank empty. Support the pl
24 Hangar 9 Taylorcraft 26cc BNFPreightCheck Your RadioBefore going to the field, be sure your batteries are fully charged per your radio’s instructi
25Hangar 9 Taylorcraft 26cc BNFVery Important Regarding your Zenoah G26 Gasoline EngineFAILURE TO READ AND FOLLOW THESE INSTRUCTIONS BEFORE YOU PROCE
26 Hangar 9 Taylorcraft 26cc BNFEngine OperationBreak-InNo specific break-in is required. The engine is gradually broken in as it is used, and the out
27Hangar 9 Taylorcraft 26cc BNF1. Start the engine without making any adjustments.2. Make adjustments only when the engine shows signs of inefficien
28 Hangar 9 Taylorcraft 26cc BNFMaintenance Chart Items Action Before Use Every 25 hours Every 100 hours Note Leakage, Check Damage/
29Hangar 9 Taylorcraft 26cc BNFItemsTypeBore x StrokeDisplacementEffective Compression RatioCarburetorAir CleanerStartingIgnitionSpark PlugMax. PowerM
3Hangar 9 Taylorcraft 26cc BNFPACKAGED INDIVIDUALLY LARGE BAGS QUANTITY USAGEFuselage with servos, batteries and pushrods (1)Right wing with ailero
30 Hangar 9 Taylorcraft 26cc BNF New ZEN Out of DateKey # Part # Part # Description Quantity1-1 ZENT207512110 ZEN2601 CYLINDER 18 ZENT20751
31Hangar 9 Taylorcraft 26cc BNFZenoah Engine Warranty and Repair PolicyWARRANTY PERIODExclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties t
32 Hangar 9 Taylorcraft 26cc BNFHangar 9 Warranty and Repair PolicyWARRANTY PERIODExclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that t
33Hangar 9 Taylorcraft 26cc BNFUNITED KINGDOMHorizon Hobby LimitedUnits 1-4 Ployters RdStaple TyeHarlow, EssexCM18 7NSUnited Kingdomsales@horizonhobby
34 Hangar 9 Taylorcraft 26cc BNFAcademy of Model Aeronautics National Model Aircraft Safety CodeEffective January 1, 2011A. GENERALA model aircraft is
35Hangar 9 Taylorcraft 26cc BNFEngine Warranty InformationEngine Type: ______________________________________________________________________________
17996Printed 02/2011© 2011 Horizon Hobby, Inc.horizonhobby.com Hangar9.comThe Spektrum trademark is used with permission of Bachmann Industries, Inc.
4 Hangar 9 Taylorcraft 26cc BNFContents of Kit and Parts Listing Safety Precautions and WarningsRead and follow all instructions and safety precaution
5Hangar 9 Taylorcraft 26cc BNFSafe Operating Recommendations• Inspectyourmodelbeforeeveryflighttomakecertainitis airworthy.• Beawareof
6 Hangar 9 Taylorcraft 26cc BNFCharging the Receiver BatteryRequired PartsFuselage assembly Receiver charger 1. Open the cockpit door by pulling on
7Hangar 9 Taylorcraft 26cc BNF 3. Remember to remove the BIND plug from the receiver BEFORE turning off the radio system. Once you have completed bin
8 Hangar 9 Taylorcraft 26cc BNF 3. Slide a #6 washer on each of the two 6-32 x 1/2-inch button head cap screws. Install the screws through the landin
9Hangar 9 Taylorcraft 26cc BNF 3. Separate the stabilizer halves. Slide the pins and one stabilizer half into the holes in the fin as shown. 4. Slid
Comments to this Manuals